Listado de la etiqueta: Windows

Memory capacity is one of the most influencing factors when buying a laptop as the whole data of the user is saved in it, moreover the Windows operating system is also installed in the memory. Upgrading the memory or installing an SSD into your laptop without reinstalling the Windows is easy and if you are looking for a quick and easy method then follow this guide.

Installing SSD in a laptop without reinstalling Windows

In the past most laptops were equipped with mechanical hard drives that had slower speed thus affecting the efficiency of the laptop. However, now mechanical hard drives are replaced with the solid-state hard drives that are much faster and contribute a lot in increasing the efficiency of the laptop. So, to install an SSD in your laptop without reinstalling the Windows follow the given steps:

Step 1: The first step is to set up the SSD by connecting it with your laptop and initializing it from the Disk Management of your laptop. Next Right click on the SSD in the Disk Management and select the option of “New Volume” from the pop-up menu and set up your SSD by following the “New Volume” setup.

Step 2: Merienda you have set up your SSD now it’s time to clone the Windows to your SSD and for that you need a third-party software which can be downloaded by clicking here.

Merienda the setup file is downloaded complete your installation process by running the downloaded file.

Step 3: Run the cloner software and click on the “Disk Clone” option where you will see your present hard drive and the SSD connected with your laptop:

At the bottom there are two options one is the Source Disk, and the other is the Target Disk so to select the disk you want to clone go to the source disk and to select which disk is to be made a clone go to the Target Disk. Here in our case Disk 0 is the source disk and Disk 1 is the target disk.

The next option is “After Finished” check the box if you want to Shut down, Restart or Hibernate your laptop and merienda you selected relevant option click on “Start” to begin the cloning process:

Step 4: Merienda the cloning is done, it’s time to change the hard drive so take the following measures:

  • Shut down your laptop and disconnect the charger
  • Disconnect the battery of the laptop if it is removable
  • Disconnect peripherals connected with the laptop

Next check the place of the laptop’s hard drive from its user manual and open the back cover of the laptop gently by using the right screwdriver. Merienda you have pulled out the hard drive, open its casing and place your SSD in the place of hard by connecting it with the laptop pins. There might be a difference of pins so first find an appropriate conversion adaptor and then plug it in. Next place the hard cover back and bolt on the screws nice and tight.

Step 5: Now turn on the laptop and it will run as corriente just like nothing has happened however you will feel the difference in its speed.

Note: Every laptop has a different design, so it is better to consult the user manual before changing the hard drive of any laptop.


Memory of a laptop plays an important role as the whole data and the operating system is saved in it, also it is a major contributing autor in the speed of laptop. If you want to avoid reinstalling the operating system while upgrading the hard drive to SSD then read this guide as I have explained how to install the SSD without reinstalling the Windows of your laptop.

Source link

Want to run Windows application on your Raspberry Pi desktop? Try out Wine. It’s a multi-format reader designed specially to run Windows applications on different platforms such as Linux, Debian, Fedora and so on. It’s a lightweight compatibility layer that efficiently runs on your Raspberry Pi desktop without reducing the device performance.

This guide will show you how you can install Wine on your Raspberry Pi device and install Windows applications with ease.

How to run Windows Applications on Raspberry Pi using Wine

Installing Wine on Raspberry Pi is pretty simple, thanks to the Raspberry Pi developers, which includes the repository of Wine, making it easier for you to install the application. The below-given steps will guide you in installing Wine in on Raspberry Pi:

Step 1: Update Raspberry Pi Packages

Before installing any application, ensure that your packages are updated. To confirm it, execute the following command:

$ sudo apt update && sudo apt upgrade

Step 2: Adding i386 Architecture

Wine works on i386 architecture and if you are using other architecture you will need to change it using the following command:

$ sudo dpkg –add-architecture i386

Step 2: Install Wine

After completing the above steps, you can install Wine on Raspberry Pi using the following command:

Enter “Y” to begin the Wine installation on your Raspberry Pi device.

After completing the installation, open Wine configuration on your Raspberry Pi device using the following command:

The above command will open the Wine configuration. You can select your Windows version according to your choice.

Installing Windows Application on Raspberry Pi

Now, to install an application on Raspberry Pi, you will first need to download a Windows application in “.exe” format.

In our case, we are going to download the VLC media player as an example for you to learn how you can install Windows applications. After the download, look for the location where your file is downloaded. It may differ in your case, but mostly, it’s located in the “Downloads” directory.

To install the application, first visit the location in the terminal using the following command:

Then use the following command to run the application using Wine.

$ wine <application_name>

Complete the remaining installation steps to install VLC media player on your Raspberry Pi OS. Then issue the following command to run the VLC media player on Raspberry Pi.

In this way, you can install multiple Windows applications with ease.


Wine is a perfect solution that allows Raspberry Pi users to install and run Windows applications easily. The installation of Wine on Raspberry Pi is quiebro simple, as mentioned in the above guidelines, it requires only an i386 architecture and an installation command. After installing, you can download any Windows application and run it on the terminal using the “wine” command with the application name.

Source link